V16

2

Specifications

CFM60M Series Derating Curve

INPUT SPECIFICATIONS:

Voltage …....………........…............................................... 90~264Vac

120~370Vdc

Frequency ………………………………………………………..... 47 to 63Hz

Inrush Current ………….… Cold Start@25℃ ............. 75A max. @240Vac

Input Current ……….………………. 100Vac/1.6A max., 240Vac/0.8Amax.

Leakage Current ……………………………………….…...…… 100uA max.

OUTPUT SPECIFICATIONS:

Hold-up Time ………………………..……………….… 16ms typ. @115Vac

Short Circuit Protection …………….....…... Hiccup Mode (Auto Recover)

Over Voltage Protection ………………...…….... TVS Component to Clamp

Temperature Coefficient ……………………............................... ±0.05%/℃

GENERAL SPECIFICATIONS:

Isolation ……………………....…… Input to output = 4000VAC (5,656VDC)

Operating Temperature (note 9) ................ -20 ~ 70℃ (see Derating Curve)

Storage Temperature …………………………....….......…............. -20~85℃

Humidity ..................................................... 93% RH max. Non-Condensing

Cooling ………………………..…………………..……..... Natural Convection

Switching Frequency …………………………………….……. 65KHz Typical

MTBF ……….… MIL-HDBK-217F, GB, 25℃/115VAC …… 200Khrs min.

Altitude ……………………..……………………….…………………… 3000m

Dimensions …….…... 4.000x2.000x1.100inches (101.60x50.80x27.94mm)

NOTE:

CFM60MXXX-CA …... 4.606x2.362x1.575inches (117.00x50.80x40.00mm)

1. Voltage accuracy is set at full load and 25℃ Ta.

Weight ……………………………………..………………………… 125g

2. Add a 0.1uF ceramic capacitor and a 10uF E.L. capacitor to output for

SAFETY AND EMC:

ripple&noise measuring @20MHz BW.

Emission and Immunity (Ed. 4.0) ……….. EN55011, EN55032 Class B, EN55024

3. Line regulation is measured from 100Vac to 240Vac with full load.

FCC CFR 47 Part 15, 18, EN61204-3, EN61000-6-1

4. Load regulation is measured from 10% to 100% full load.

EN61000-6-3, EN60601-1-2, EN61000-3-2, EN61000-3-3

5. Typical Efficiency at 230 VAC and Full Load at 25°C

Safety (Ed. 3.1) …. Class I, IEC60601-1:2005+A1:2012, EN60601-1:2006/A1:2003

6. Standard input and output connectors (CN1 and CN2) wafer with

UL ANSI/AAMI ES60601-1:2005, IEC60950-1, EN60950-1, UL60950-1

TAIWAN KING PIN TERMINAL PVHI series and mate with JST housing

VHR series and JST SVH-21/41T-P1.1 series crimp terminal or Equivalent.

7. Optional Input and output connectors (CN1 and CN2) wafer with

LONG CHU P3060 series and mate with MOLEX housing 5195 series

and MOLEX 5194 series crimp terminal or equivalent.

8. Safety approvals do not apply to the covered versions, only to the open frame versions.

9. Others model refer to application note.

Mechanical Specification

0.150[3.80]

4.000[101.60]

3.701[94.00]

All Dimensions in Inches[mm]

Tolerance Inches:x.xxx±0.02

Millimeters:x.xx±0.5

ACL

CN1

ACN

PE

PE

CN2

1

2

3

4

LED

Output connector CN2

Pin 1

+ Vout

VR

Pin 2

Pin 3

Input connector CN1

Pin 1

Line

Not Fitted

Pin 2

Neutral

Pin 3

Pin 4

+ Vout

- Vout

- Vout

0.236[6.00]

4.606[117.00]

0.846[21.50]

3.701[94.00]

0.236[6.00]

2.441[62.00]

0.039[1.00]

2.362[60.00]

CFM60MXXX

4-Φ

0.1

25

[Φ

3.1

8]

CFM60MXXX-CA

4-

M

3x

0.5

P

Typical at 25˚C, nominal line and 75% load, unless otherwise Specified

Open Frame versions:

Covered versions:

CFM60M050-CA