AM652X datasheet(253/277 Pages) TI1

253 / 277 page

253

AM6548, AM6528, AM6546

AM6526, AM6527

www.ti.com

SPRSP08I – NOVEMBER 2017 – REVISED DECEMBER 2019

Submit Documentation Feedback

Product Folder Links: AM6548 AM6528 AM6546 AM6526 AM6527

Applications, Implementation, and Layout

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test design implementation to confirm system functionality.

7.1

Device Connection and Layout Fundamentals

7.1.1

Power Supply Decoupling and Bulk Capacitors

7.1.1.1

Power Distribution Network Implementation Guidance

The Sitara™ Processor Power Distribution Networks: Implementation and Analysis provides guidance for

successful implementation of the power distribution network. This includes PCB stackup guidance as well

as guidance for optimizing the selection and placement of the decoupling capacitors. TI supports only

designs that follow the board design guidelines contained in the application report.

7.1.2

External Oscillator

For more information, see Section 5.9.4.1, Input Clocks / Oscillators.

7.1.3

JTAG and EMU

Texas Instruments supports a variety of eXtended Development System (XDS) JTAG controllers with

various debug capabilities beyond only JTAG support. A summary of this information is available in the

XDS Target Connection Guide.

For more recommendations on EMU routing, see Emulation and Trace Headers Technical Reference

Manual.

7.1.4

Reset

The device incorporates four external reset pins (MCU_PORz, MCU_RESETz, PORz, and RESETz) and

four reset status pins (MCU_PORz_OUT, MCU_RESETSTATz, PORz_OUT, and RESETSTATz).

Additional reset modes are available through internal registers and emulation.

The device integrates an on-chip Power-on-Reset (POR) generator. Additionally, this device supports an

external POR generation through a PORz and MCU_PORz input pin. The MCU_BYPASS_POR pin

selects the POR source. When the MCU_BYPASS_POR pin is set high at power-up, on-chip POR

generation will be completely bypassed and the external POR used. When it is low, the POR is generated

internally. However, the four external reset inputs must all be pulled high to enable this internal POR

generation.

7.1.5

Unused Pins

For more information about Unused Pins, see Section 4.5, Connections for Unused Pins.

7.1.6

Hardware Design Guide for AM65x/DRA80xM Devices

The Hardware Design Guide for AM65x/DRA80xM Devices document describes hardware system design

considerations for the AM65x/DRA80xM family of processors.This design guideis intended to be used as

an aid during the development of application hardware.

AM652X Folha de dados(PDF) 253 Page - Texas Instruments

AM652X Folha de dados(HTML) 253 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL