Os motores de busca de Datasheet de Componentes eletrônicos
  Portuguese  ▼
ALLDATASHEETPT.COM

X  

ISL6505 Folha de dados(PDF) 13 Page - Renesas Technology Corp

Nome de Peças ISL6505
Descrição Electrónicos  Multiple Linear Power Controller with ACPI Control Interface
PDF  18 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrônico  RENESAS [Renesas Technology Corp]
Página de início  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

ISL6505 Folha de dados(HTML) 13 Page - Renesas Technology Corp

Back Button ISL6505 Datasheet HTML 9Page - Renesas Technology Corp ISL6505 Datasheet HTML 10Page - Renesas Technology Corp ISL6505 Datasheet HTML 11Page - Renesas Technology Corp ISL6505 Datasheet HTML 12Page - Renesas Technology Corp ISL6505 Datasheet HTML 13Page - Renesas Technology Corp ISL6505 Datasheet HTML 14Page - Renesas Technology Corp ISL6505 Datasheet HTML 15Page - Renesas Technology Corp ISL6505 Datasheet HTML 16Page - Renesas Technology Corp ISL6505 Datasheet HTML 17Page - Renesas Technology Corp Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 18 page
background image
ISL6505
FN9109 Rev 3.00
Page 13 of 18
Dec 1, 2005
attention has to be paid to the few potentially sensitive small
signal components, such as those connected to sensitive
nodes or those supplying critical bypass current.
The power components (pass transistors) and the controller
IC should be placed first. The controller should be placed in a
central position on the motherboard, closer to the memory
controller chip and processor, but not excessively far from the
3.3VDUAL island or the I/O circuitry. Ensure the 1V2VID, 3V3,
and 3V3DL connections are properly sized to carry 100mA
without exhibiting significant resistive losses at the load end.
Similarly, the input bias supply (5VSB) can carry a significant
level of current - for best results, ensure it is connected to its
respective source through an adequately sized trace. The
pass transistors should be placed on pads capable of
heatsinking matching the device’s power dissipation. Where
applicable, multiple via connections to a large internal plane
can significantly lower localized device temperature rise.
Placement of the decoupling and bulk capacitors should follow a
placement reflecting their purpose. As such, the high-frequency
decoupling capacitors should be placed as close as possible to
the load they are decoupling; the ones decoupling the controller
close to the controller pins, the ones decoupling the load close
to the load connector or the load itself (if embedded). Even
though bulk capacitance (aluminum electrolytics or tantalum
capacitors) placement is not as critical as the high-frequency
capacitor placement, having these capacitors close to the load
they serve is preferable.
The critical small signal components include the soft-start
capacitor, CSS, as well as all the high-frequency decoupling
capacitors. Locate these components close to the respective
pins of the control IC, and connect them to ground through a
via placed close to the ground pad. Minimize any leakage
current paths from the SS node, as the internal current source
is only 10µA (typical).
A multi-layer printed circuit board is recommended.
Figure 12 shows the connections to most of the components in
the circuit. Note that the individual capacitors shown each
could represent numerous physical capacitors. Dedicate one
solid layer for a ground plane and make all critical component
ground connections through vias placed as close to the
component terminal as possible. Dedicate another solid layer
as a power plane and break this plane into smaller islands of
common voltage levels. Ideally, the power plane should
support both the input power and output power nodes. Use
copper filled polygons on the top and bottom circuit layers to
create power islands connecting the filtering components
(output capacitors) and the loads. Use the remaining printed
circuit layers for small signal wiring.
Component Selection Guidelines
Output Capacitors Selection
The output capacitors should be selected to allow the output
voltage to meet the dynamic regulation requirements of active
state operation (S0, S1). The load transient for the various
microprocessor system’s components may require high quality
capacitors to supply the high slew rate (di/dt) current demands.
Thus, it is recommended that the output capacitors be selected
for transient load regulation, paying attention to their parasitic
components (ESR, ESL).
Also, during the transition between active and sleep states on
the 3.3VDUAL/3.3VSB and 5VDUAL outputs, there is a short
interval of time during which none of the power pass elements
are conducting - during this time the output capacitors have to
supply all the output current. The output voltage drop during
this brief period of time can be easily approximated with the
following formula:
, where
VOUT - output voltage drop
ESROUT - output capacitor bank ESR
IOUT - output current during transition
COUT - output capacitor bank capacitance
tt - active-to-sleep or sleep-to-active transition time (10s typ.)
VOUT1
CHF1
FIGURE 12. PRINTED CIRCUIT BOARD ISLANDS
VOUT3
Q2
Q3
Q4
CSS
+12VIN
CIN
VIA CONNECTION TO GROUND PLANE
ISLAND ON POWER PLANE LAYER
ISLAND ON CIRCUIT/POWER PLANE LAYER
ISL6505
VOUT4
SS
GND
5VDLSB
3V3DLSB
KEY
5VSB
+5VSB
DLA
Q5
CBULK4
C5VSB
CHF3
CHF4
5VDL
+5VIN
+3.3VIN
3V3DL
3V3
DR1
CBULK2
CHF2
CBULK1
1V2VID
CBULK3
VOUT2
5V
FB1
Q6
VOUT
IOUT ESROUT
tt
COUT
----------------
+



=



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18


Folha de dados Download

Go To PDF Page


Ligação URL



ALLDATASHEET é útil para você?  [ DONATE ] 

Sobre Alldatasheet   |   Publicidade   |   Contato conosco   |   Privacy Policy   |   Link para a ficha técnica    |   roca de Link   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com