| Os motores de busca de Datasheet de Componentes eletrônicos |
|
TDA8920B Folha de dados(PDF) 15 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
TDA8920B Folha de dados(HTML) 15 Page - NXP Semiconductors |
|
15 / 34 page ![]() 9397 750 13356 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Preliminary data sheet Rev. 01 — 1 October 2004 15 of 34 Philips Semiconductors TDA8920B 2 × 100 W class-D power amplifier 12.3 Mono BTL application [1] RsL is the series resistance of inductor of low-pass LC filter in the application. [2] Output power is measured indirectly; based on RDSon measurement. See also Section 13.3. [3] Total harmonic distortion is measured in a bandwidth of 22 Hz to 20 kHz, using an AES17 20 kHz brickwall filter. Maximum limit is guaranteed but may not be 100 % tested. [4] Vripple =Vripple(max) = 2 V (p-p); Rs =0 Ω. [5] B = 22 Hz to 20 kHz, using an AES17 20 kHz brickwall filter. [6] B = 22 Hz to 20 kHz, using an AES17 20 kHz brickwall filter; independent of Rs. [7] Vi =Vi(max) = 1 V (RMS); fi = 1 kHz. 13. Application information 13.1 BTL application When using the power amplifier in a mono BTL application the inputs of both channels must be connected in parallel and the phase of one of the inputs must be inverted (see Figure 6). In principle the loudspeaker can be connected between the outputs of the two single-ended demodulation filters. Table 10: Mono BTL application characteristics VP = ±27 V; RL =8 Ω; fi = 1 kHz; fosc = 317 kHz; RsL < 0.1 Ω [1]; Tamb =25 °C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Po output power RL =6 Ω; VP = ±27 V [2] THD = 0.5 % - 174 - W THD = 10 % - 210 - W RL =8 Ω; VP = ±27 V [2] THD = 0.5 % - 138 - W THD = 10 % - 173 - W THD total harmonic distortion Po =1W [3] fi = 1 kHz - 0.02 0.05 % fi = 6 kHz - 0.03 - % Gv(cl) closed loop voltage gain 35 36 37 dB SVRR supply voltage ripple rejection operating [4] fi = 100 Hz - 80 - dB fi = 1 kHz 70 80 - dB mute; fi = 100 Hz [4] -80 - dB standby; fi = 100 Hz [4] -80 - dB Zi input impedance 22 34 - k Ω Vn(o) noise output voltage operating Rs =0 Ω [5] - 300 - µV mute [6] - 220 - µV Vo(mute) output signal in mute [7] - 200 - µV CMRR common mode rejection ratio Vi(CM) = 1 V (RMS) - 75 - dB |
|
Ligação URL |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | Link para a ficha técnica | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |