408-9935 datasheet(3/6 Pages) MACOM

Nome de Peças	408-9935

Descrição Electrónicos	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.

Download	6 Pages

Scroll/Zoom	100%

Fabricante Electrônico	MACOM [Tyco Electronics]

Página de início	http://www.macom.com

Logo

3 / 6 page

408- 9935

PRO- CRIMPER III Hand Crimping Tool Assembly 90683- 1

3

of 6

Rev C

Tyco Electronics Corporation

4. CONTACT SUPPORT ADJUSTMENT (Figure 3

)

The contact support is preset prior to shipment,

but minor adjustment may be necessary.

1. Make a sample crimp and determine if the

contact is straight, bending upward, or bending

downward.

2. If adjustment is required, loosen the screw that

holds the contact support onto the locator

assembly.

The ratchet has detents that create audible clicks

as the tool handles are closed.

3. Place a contact with wire into the proper nest

and close the tool handles until the ratchet reaches

the sixth click, or until the contact support touches

the contact.

4. Slightly loosen the nut that holds the locator

assembly onto the tool frame.

5. Move the contact support as required to

eliminate the bending of the contact.

6. Tighten the nut and close the handles until the

ratchet releases.

7. Remove and inspect the contact.

8. Make another sample crimp. If the contact is

straight, tighten the contact support screw. If the

contact is still being bent during crimping, repeat

the adjustment procedure.

5. CRIMPING PROCEDURE

This tool is provided with a crimp adjustment

feature. Initially, the crimp height should be

verified as specified in Figure 4. Refer to

Section 6, CRIMP HEIGHT INSPECTION, and

Section 7, RATCHET ADJUSTMENT, to verify

crimp height before using the tool to crimp

desired contacts and wire sizes.

Refer to the table in Figure 1 and select wire of the

specified size and insulation diameter. Strip the wire

to the length indicated in Figure 1, taking care not to

nick or cut wire strands. Select an applicable contact

and identify the appropriate crimp section according

to the wire size markings on the tool. Refer to

Figure 3 and proceed as follows:

1. Hold the tool so that the back (wire side) is

facing you. Squeeze tool handles together and

allow them to open fully.

2. Holding the contact by the mating end, insert the

contact — insulation barrel first — through the front

of the tool and into the appropriate crimp section.

3. Position the contact so that the mating end of

the contact is on the locator side of the tool, and so

that the open “U” of the wire and insulation barrels

face the top of the tool. Place the contact up into

the nest so that the movable locator drops into the

slot in the contact. Refer to Figure 3. Butt the front

end of the wire barrel against the movable locator.

Make sure that both sides of the insulation barrel

are started evenly into the crimping section. Do

NOT attempt to crimp an improperly positioned

contact.

Figure 3

Adjustment

Screw for

Contact Support

Contact

Support

Locator

Back of Tool

(Wire Side)

Wire

Contact

(Typ)

Strip

Length

Locator in

Wire Stop Slot

Wire Inserted

to Stop

NOTE

i

NOTE

i

NOTE

i

CAUTION

!

Nº de peça semelhante - 408-9935

Fabricante Electrônico	Nome de Peças	Folha de dados	Descrição Electrónicos
TE Connectivity Ltd	408-9930	240Kb / 4P	PRO-CRIMPER* III Hand Crimping
Tyco Electronics	408-9933	247Kb / 6P	PRO-CRIMPER* III Hand
Tyco Electronics	408-9934	247Kb / 6P	PRO-CRIMPER* III Hand
TE Connectivity Ltd	408-9938	314Kb / 5P	PRO-CRIMPER III Hand Crimping Tool Assembly
Tyco Electronics	408-9938	314Kb / 5P	The die assembly features a wire anvil, an insulation anvil, a wire crimper, and an insulation crimper

More results

Descrição semelhante - 408-9935

Fabricante Electrônico	Nome de Peças	Folha de dados	Descrição Electrónicos
TE Connectivity Ltd	408-1216	91Kb / 2P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools
Tyco Electronics	408-8607	247Kb / 6P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
TE Connectivity Ltd	408-9359	210Kb / 7P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
	408-10110	191Kb / 5P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
	408-6561	110Kb / 4P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
Tyco Electronics	408-9039	103Kb / 5P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools
	408-9240	85Kb / 3P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
	408-8377	249Kb / 6P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools
	408-10324	239Kb / 5P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools
	411-3236	216Kb / 5P	Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.

More results

408-9935 Folha de dados(PDF) 3 Page - Tyco Electronics

408-9935 Folha de dados(HTML) 3 Page - Tyco Electronics

Nº de peça semelhante - 408-9935

Descrição semelhante - 408-9935

Html Pages

1 2 3 4 5 6

Folha de dados Download

Ligação URL