 |
Os motores de busca de Datasheet de Componentes eletrônicos |
|
|
Os motores de busca de Datasheet de Componentes eletrônicos |
|
408-4260 Folha de dados(PDF) 6 Page - Tyco Electronics |
|
|
|||||||||||||||||||||||||||||
408-4260 Folha de dados(HTML) 6 Page - Tyco Electronics |
|
|
6 / 7 page  408- 4260 MTA 58575- 1 and 58576- 1 Rev D 6 of 7 Tyco Electronics Corporation 2. Grasp the applicator assembly handle and hold the applicator assembly over the connector-- holding fixture so that the guides align with the ends of the fixture as shown in Figure 3. Figure 3 Connector--Holding Fixture Note: For clarity, harness board is not shown. Do not use this tool as a blunt object, a crushing device, or for any purpose other than crimping the proper specified product. Inappropriate use of the tool could result in personal injury or damage to the tool. 3. Gently push the applicator assembly onto the fixture until the safety latches engage the fixture and the insertion tooling sits flat on the connector. 4. Depress the trigger to actuate the applicator assembly. 5. Remove the terminated connector from the fixture, and inspect the connector according to Application Specification 114--1019 (MTA .100) or 114--1020 (MTA .156). 5. INSERTION- DEPTH ADJUSTMENT To avoid personal injury, DISCONNECT applicator assembly from air supply before making any adjustments. If, after inspection, the wire insertion depth measurement is not in accordance, adjust the applicator assembly according to the following. The applicator assembly insertion depth is factory preset and should not require adjusting; however, number of conductors, air pressure, wire size, and wire insulation diameter can affect insertion depth measurements. Always verify the insertion depth setting using a test sample before making any adjustments. 1. Insert a small--diameter punch into the insertion depth adjustment slot (refer to Figure 1), and rotate the wheel clockwise to decrease the insertion depth setting; counterclockwise to increase the insertion depth. Each click of the wheel adjusts the insertion depth setting by 0.10 mm [.004 in.]. 2. When the applicator assembly is actuated, the safety latches should slightly touch the guides. If they do not, turn each safety latch adjustment screw (located on the lower side of the latch) clockwise in small increments until latches move properly. 6. MAINTENANCE AND INSPECTION Each applicator assembly is assembled and inspected before shipment. It is recommended that the applicator assembly be inspected immediately upon arrival in your plant to ensure that it has not been damaged during shipment. 6.1. Daily Maintenance It is recommended that each operator be made aware of, and responsible for, the following steps of daily maintenance: 1. Remove dust, moisture, and other contaminants with a clean, soft brush or clean lint--free cloth. Do NOT use objects that could damage the applicator assembly or any of its components. 2. Ensure that the screws are in place and secured. 3. When the applicator assembly is not in use, store it in a clean, dry area. 6.2. Periodic Inspection Regular inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the applicator assembly or be supplied to personnel responsible for the applicator assembly. The inspection frequency should be based on the amount of use, working conditions, operator training and skill, and established company standards. At a minimum, the tool should be inspected on a weekly basis. CAUTION ! DANGER CAUTION ! NOTE i |
Nº de peça semelhante - 408-4260 |
|
Descrição semelhante - 408-4260 |
|
|
|
Ligação URL |
| Privacy Policy |
| ALLDATASHEETPT.COM |
| ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Portuguese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
