PIC16C71 datasheet(229/337 Pages) MICROCHIP

229 / 337 page

DS30234D-page 229

PIC16C6X

Applicable Devices 61 62 62A R62 63 R63 64 64A R64 65 65A R65 66 67

FIGURE 20-10: I2C BUS DATA TIMING

TABLE 20-10: I2C BUS DATA REQUIREMENTS

Parameter

No.

Sym

Characteristic

Min

Max

Units

Conditions

100

THIGH

Clock high time

100 kHz mode

4.0

—

µs

Device must operate at a min-

imum of 1.5 MHz

400 kHz mode

0.6

—

µs

Devce must operate at a mini-

mum of 10 MHz

SSP Module

1.5TCY

—

101

TLOW

Clock low time

100 kHz mode

4.7

—

µs

Device must operate at a min-

imum of 1.5 MHz

400 kHz mode

1.3

—

µs

Device must operate at a min-

imum of 10 MHz

SSP Module

1.5TCY

—

102

SDA and SCL rise

time

100 kHz mode

—

1000

400 kHz mode

20 + 0.1Cb

300

Cb is speciﬁed to be from

10-400 pF

103

SDA and SCL fall time

100 kHz mode

—

300

400 kHz mode

20 + 0.1Cb

300

Cb is speciﬁed to be from

10-400 pF

TSU:STA

START condition

setup time

100 kHz mode

4.7

—

µs

Only relevant for repeated

START condition

400 kHz mode

0.6

—

µs

THD:STA

START condition hold

time

100 kHz mode

4.0

—

µs

After this period the ﬁrst clock

pulse is generated

400 kHz mode

0.6

—

µs

106

THD:DAT

Data input hold time

100 kHz mode

—

400 kHz mode

0.9

µs

107

TSU:DAT

Data input setup time

100 kHz mode

250

—

Note 2

400 kHz mode

100

—

TSU:STO

STOP condition setup

time

100 kHz mode

4.7

—

µs

400 kHz mode

0.6

—

µs

109

TAA

Output valid from

clock

100 kHz mode

—

3500

Note 1

400 kHz mode

—

110

TBUF

Bus free time

100 kHz mode

4.7

—

µs

Time the bus must be free

before a new transmission

can start

400 kHz mode

1.3

—

µs

Bus capacitive loading

—

400

Note 1:

As a transmitter, the device must provide this internal minimum delay time to bridge the undeﬁned region (min. 300 ns) of

the falling edge of SCL to avoid unintended generation of START or STOP conditions.

A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the requirement

tsu;DAT

≥ 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the

SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line

TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus speciﬁcation) before the SCL line is

released.

Note: Refer to Figure 20-1 for load conditions

100

101

103

106

107

109

110

102

SCL

SDA

Out

PIC16C71 Folha de dados(PDF) 229 Page - Microchip Technology

PIC16C71 Folha de dados(HTML) 229 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL