E5DC-RX2DSM-017 datasheet(115/120 Pages) OMRON

115 / 120 page

@C/E5@C-T

115

• If you use crimp terminals for the E5DC, use crimp terminals with

insulation sleeves. If you use a bare crimp terminal with no

insulation, the terminal may short with the terminal above or below

it. If you use bare crimp terminals, cover the crimped sections with

insulating marking tubes. Secure the marking tubes so that they do

not move.

Although you can connect two crimp terminals with insulation

sleeves to one terminal, you cannot do so if the diameter of the

insulation sleeves is too large.

Recommended Crimp Terminals with Insulation Sleeves for the E5DC

E5GC (Controllers with Screwless Clamp

Terminal Blocks)

1. Connection Method for Screwless Clamp Terminals

The same method is used to connect stranded wires, solid wires, and

ferrules.

Part Names of the Terminal Block

Connection Method

1. Press the pusher with a flat-blade screwdriver.

2. With the screwdriver still pressing the pusher, insert the wire into

the terminal (Insertion) hole.

3. Remove the flat-blade screwdriver from the pusher.

Checking Connections

• After insertion, pull gently on the wire to make sure that it will not

come out (i.e., to confirm that it is held by the terminal block).

2. Removal Method for Screwless Clamp Terminals

The same method is used to remove stranded wires, solid wires, and

ferrules.

1. Press the pusher with a flat-blade screwdriver.

2. With the screwdriver still pressing the pusher, pull the wire out of

the terminal (Insertion) hole.

3. Remove the flat-blade screwdriver from the pusher.

3. Recommended Wire Size and Ferrules

Wire Size

Use the wire sizes and stripping lengths given in the following table.

Ferrules

Ferrules must be 0.8 to 1.4 mm in diameter.

The exposed conductor inserted into the terminal must be 8 to 12 mm

in length.

Recommended ferrules

Manufacturer

Model number

J.S.T. Mfg. Co.

V1.25-B3A

V0.5-3A

Pusher

Terminal (Insertion) hole

(1)

(2)

(3)

Wire Size

Stripping length

AWG24 to AWG18

(0.21 to 0.82 mm2)

8 to 12 mm

Manufacturer name

Model number

Altech Corp.

2623.0

Daido Solderless Terminal Mfg. Co.

AVA-0.5

J.S.T. Mfg. Co.

TUB-0.5

Nichifu Co., Ltd.

Single (1 wire)

TGNTC-1.25-9T

TGVTC-1.25-11T

TGNTC-1.25-11T

TC0.3-9.5

TC1.25-11S-ST

TC1.25-11S

TC2-11S

Double (2 wires)

TGWVTC-1.25-9T

TGWVTC-1.25-11T

(1)

(2)

(3)

0.8 to 1.4mm

8 to 12mm

E5DC-RX2DSM-017 Folha de dados(PDF) 115 Page - Omron Electronics LLC

E5DC-RX2DSM-017 Folha de dados(HTML) 115 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Folha de dados Download

Ligação URL